R
Ralph
Guest
My old MFDBB has died. I sent it to Furuno Italy and they could not repair it anymore.
So I decided to buy a tested replacement MFDBB from the US ( I am from Austria)
I got the box last week and now I brought it to Italy on my boat to install.
All went fine:
I installed the new box. ALL was working great.
I did the installation wizzard and set all the ports and Nicknames( I made Photos while my old box was running).
I then tested everything, updated my MFD12 to Version 2.13 and all worked well. I then wanted to create some Points and Routed with the mouse, but that did not work.
I then tried to create pionts or new routes also with the MCU Keyboard. Also this was not possible.
So I thought I might do a master restet, maybe there where some old information’s regarding points and routes. So I disconnected everything and tried to restart again.
The system was booting fine, but now it does not detect my MCU anymore. It boots fine to the initial Navigation Warning. „Push Rotokey to Agree“, but it does not take the RotoKey.
I wanted to make a master reset (I bought a USB Keyboard for this), but by any reason, it does not do the master reset. I am pressing the ESC Key according to the instruction, but after 2 Minutes it still comes up with the yellow start screen (Navigation Warning – Push Roto Key to Agree)
Now I don’t know what to do. (I have even prepared a 2.13 update boote stick – just in case-but the new box had 2.13 already installed). But I also can not try to insert the boot stick, since I cannot perform the master reset to disable the DHCP (Master off).
I think there is just some missconfiguration, but I don’t know how to force the MFDBB to start with the installation waizzard again ( it worked fine, when I did the initial first Installation)
Maybe someone has some tipp for me? Is there another method to force a master reset (I read in the instruction, that some Keyboards don’t work if the don’t repeat the command). Maybe this Keyboard is one of them.
I also tried the MCU MFDBB connetction reset (left sroll +right cursor + 5 sec RotoKey). No double beep of the MCU. When I disconnect the ethernet cabe and reconnet the MCU double beeps.
Since it worked the whole Afternoon, before I did the disconnction of all, the MCU should be fine.
What else can I try, that it is starting with the installation wizzard or other method to do a master rest?
what happens if I try to boot with the USB incremantal Update stick 2.13 when the MFDBB ist still the master and no master reset was performed before? I don't want to try it, because the manual says it MUST be configured as slave and I must perfom a master reset before.
Any help appreciated! Thanks, Ralph
So I decided to buy a tested replacement MFDBB from the US ( I am from Austria)
I got the box last week and now I brought it to Italy on my boat to install.
All went fine:
I installed the new box. ALL was working great.
I did the installation wizzard and set all the ports and Nicknames( I made Photos while my old box was running).
I then tested everything, updated my MFD12 to Version 2.13 and all worked well. I then wanted to create some Points and Routed with the mouse, but that did not work.
I then tried to create pionts or new routes also with the MCU Keyboard. Also this was not possible.
So I thought I might do a master restet, maybe there where some old information’s regarding points and routes. So I disconnected everything and tried to restart again.
The system was booting fine, but now it does not detect my MCU anymore. It boots fine to the initial Navigation Warning. „Push Rotokey to Agree“, but it does not take the RotoKey.
I wanted to make a master reset (I bought a USB Keyboard for this), but by any reason, it does not do the master reset. I am pressing the ESC Key according to the instruction, but after 2 Minutes it still comes up with the yellow start screen (Navigation Warning – Push Roto Key to Agree)
Now I don’t know what to do. (I have even prepared a 2.13 update boote stick – just in case-but the new box had 2.13 already installed). But I also can not try to insert the boot stick, since I cannot perform the master reset to disable the DHCP (Master off).
I think there is just some missconfiguration, but I don’t know how to force the MFDBB to start with the installation waizzard again ( it worked fine, when I did the initial first Installation)
Maybe someone has some tipp for me? Is there another method to force a master reset (I read in the instruction, that some Keyboards don’t work if the don’t repeat the command). Maybe this Keyboard is one of them.
I also tried the MCU MFDBB connetction reset (left sroll +right cursor + 5 sec RotoKey). No double beep of the MCU. When I disconnect the ethernet cabe and reconnet the MCU double beeps.
Since it worked the whole Afternoon, before I did the disconnction of all, the MCU should be fine.
What else can I try, that it is starting with the installation wizzard or other method to do a master rest?
what happens if I try to boot with the USB incremantal Update stick 2.13 when the MFDBB ist still the master and no master reset was performed before? I don't want to try it, because the manual says it MUST be configured as slave and I must perfom a master reset before.
Any help appreciated! Thanks, Ralph